Ruckus Wireless ZoneFlex R310 manual

Ruckus Wireless ZoneFlex R310
(1)
  • Número de páginas: 4
  • Tipo de archivo: PDF
Copyright © 2015 Ruckus Wireless, Inc. Page 1 of 4
Published 24 July 2015, Part Number 800-70972-001 Rev A

ZoneFlex R310 Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instructions on how to set up
your Ruckus Wireless ZoneFlex R310 access point. After completing the
steps in this guide, you will be able to place the access point at your site
and provide network access to wireless clients. The rest of this document
refers to the ZoneFlex R310 access point as an AP.
BEFORE YOU BEGIN
Before deploying your Ruckus Wireless device, please check the Ruckus
Wireless Web site for the latest software and release documentation.
• Release Notes and User Documents are available at
http://support.ruckuswireless.com/documents
• Software Upgrades are available at
http://support.ruckuswireless.com/software
• Open Source information is available at
http://support.ruckuswireless.com/open_source
THIS GUIDE IN OTHER LANGUAGES
请从以下网站获得该指南的简体中文版
https://support.ruckuswireless.com
• Vous trouverez la version française de ce guide à l'adresse suivante
https://support.ruckuswireless.com
日本語版 https://support.ruckuswireless.com
でご覧く ださい
가이드의 한국어 버전은 사이트
(https://support.ruckuswireless.com
) 에서 확인하시기 바랍니
• Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com
• Puede ver la versión en español (América Latina) de esta guía en
https://support.ruckuswireless.com
Figure 1. ZoneFlex R310 AP

PACKAGE CONTENTS

• One ZoneFlex R310 access point
• Two mounting screws and plastic wall anchors
• One T8 5mm M2.5 Torx locking security screw
• One unit removal pin
• Regulatory flyer
• Product warranty statement
• Declaration of conformity, if required
• Ruckus Wireless AP Getting Started Guide
•This Quick Setup Guide

CONFIGURING THE AP

Step 1: Collecting the AP MAC Address
Step 2: Collecting Setup Requirements, Hardware, and Tools
Step 3: Connecting Your Computer to the AP
Step 4: Preparing Your Computer for AP Setup
Step 5: Logging Into the AP Web Interface
Step 6: Customizing the Wireless Settings
Step 7: Placing the AP at the Site
Step 8: Verifying the Installation
Step 1: Collecting the AP MAC Address
• Write down the MAC address (12 alphanumeric digits) from the
outside of the AP.
Step 2: Collecting Setup Requirements, Hardware,
and Tools
• A computer with Ethernet adapter running Windows 7 or equivalent,
with Firefox or equivalent web browser.
• One Cat 5e (or better) Ethernet cable.
• T8 Torx screwdriver.
• An AC-to-12VDC power adapter (sold separately)
--OR--
an 802.3af-compliant Power over Ethernet (PoE) switch or PoE
injector.
Step 3: Connecting Your Computer to the AP
A After removing the AP from its package, place it next to your
computer.
B Using an Ethernet cable, connect your computer’s network port to the
POE IN port on the AP.
C Connect the AC power adapter (sold separately) to the 12VDC AP
port, and plug the AC power adapter into a convenient and protected
AC power source.
Alternatively, connect the POE IN port to a PoE injector or PoE switch
for both power and network connectivity.
Figure 2. AP rear panel
D After bootup, verify that the PWR LED on the AP is a steady green.
Step 4: Preparing Your Computer for AP Setup
A On your Windows 7 computer, configure your network adapter from
the Local Area Connection settings as follows:
• Start > Control Panel > Network and Sharing
Center > Change Adapter Settings
Note:
The minimum software revision for the AP is base image 100.x or
later, SmartZone 3.2 or later, or ZoneFlex 10.0 or later.
The rest of this document collectively refers to the SCG SZ, vSZ, ZD,
and other controllers as Ruckus Wireless controllers.
Important!
If the AP is to be managed by a Ruckus Wireless controller, then
follow the controller user documents to connect the AP to your local
network and configure it for initial operation. In that case, you may not
need to complete the following steps.
Note:
The following procedures assume that Windows 7 is the operating
system. Procedures for other operating systems are similar.
Ruckus Wireless ZoneFlex R310

¿Necesitas ayuda?

Número de preguntas: 0

¿Tienes alguna pregunta sobre Ruckus Wireless ZoneFlex R310 o necesitas ayuda? Haz tu pregunta aquí. Proporciona una descripción clara y completa de tu consulta. Cuantos más detallada sea tu consulta, más fácil será para otros Ruckus Wireless ZoneFlex R310 propietarios responder adecuadamente a tu pregunta.

Ruckus Wireless ZoneFlex R310 especificaciones

General
Marca Ruckus Wireless
Modelo ZoneFlex R310
Producto Punto de acceso
Idioma Inglés
Tipo de archivo PDF
Características
Rango máximo de transferencia de datos 867 Mbit/s
Ethernet LAN, velocidad de transferencia de datos 10,100,1000 Mbit/s
2.4 GHz Si
5 GHz Si
Calidad de servicio (QoS) soporte Si
Soporte VLAN Si
Estándares de red IEEE 802.11a,IEEE 802.11ac,IEEE 802.11b,IEEE 802.11g,IEEE 802.11n
Características de administración
Administración basada en web Si
Protocolos
DHCP, servidor Si
Puertos e Interfaces
Puertos Ethernet LAN (RJ-45) 1
Enchufe de entrada de CC Si
Cantidad de puertos USB 2.0 0
Seguridad
Algoritmos de seguridad WPA-PSK,WPA-TKIP,WPA2-AES
Antena
Características de la antena Antena integrada
Control de energía
Consumo energético 7.1 W
Consumo de energía (máx.) 9 W
Energía sobre Ethernet (PoE) Si
Voltaje de salida 12 V
Corriente de salida 1 A
Diseño
Interno Si
Ranura para cable de seguridad Si
Color del producto Blanco
Ubicación Table,Wall
Tipo de ranura de bloqueo del cable Kensington
Condiciones ambientales
Intervalo de humedad relativa para funcionamiento 10 - 95 %
Intervalo de temperatura operativa (T-T) 0 - 40 °C
Peso y dimensiones
Ancho 135 mm
Profundidad 138 mm
Altura 33 mm
Peso 220 g
mostrar más

Preguntas frecuentes

A continuación, encontrarás las preguntas más frecuentes sobre Ruckus Wireless ZoneFlex R310.

¿No aparece tu pregunta? Haz tu pregunta aquí