Lancom WLC-30 manual

Lancom WLC-30
7.5 · 1
PDF manual
 · 1 pagina
manualLancom WLC-30
Power supply 12 V DC, external power adapter (110 or 230 V) with bayonet connector to secure against
Power consumption Max. 8.5 W
Environment Temperature range 0–40 °C; humidity 0–95 %; non-condensing
Housing Robust synthetic housing, rear connectors, ready for wall mounting, Kensington lock; mea-
sures 210 x 45 x 140 mm (W x H x D)
Number of fans None; fanless design, no rotating parts, high MTBF
Uplink 10 / 100 / 1000 Mbps Gigabit Ethernet
ETH 4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet.
Each Ethernet port can be freely configured (LAN, WAN, monitor port, off). LAN ports operate
in switch mode or isolated. Additionally, external DSL modems or termination routers can be
operated at the Uplink port together with policy-based routing.
USB USB 2.0 Hi-Speed host port for connecting USB printers (USB print server) or USB data media
(FAT file system)
Config (Com) Serial configuration interface / COM port (8-pin Mini-DIN): 9,600 - 115,000 baud, suitable for
optional connection of analog / GPRS modems. Supports the internal COM-port server.
WAN protocols
Ethernet PPPoE, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and plain Ethernet (with or without DHCP),
RIP-1, RIP-2, VLAN, IP, GRE, L2TPv2 (LAC or LNS), IPv6 over PPP (IPv6 and IPv4/IPv6 Dual
Stack Session), IP(v6)oE (autoconfiguration, DHCPv6 or static)
Declaration of conformity
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in
compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of
the EU Declaration of Conformity is available at the following Internet address:
Package content
Documentation Quick Reference Guide (DE/EN), Installation Guide (DE/EN)
Cable Ethernet cable, 3m (kiwi-colored connectors)
WLC Public Spot Function included in firmware
Power adapter External power adapter, 12 V / 2 A DC, barrel connector 2.1 / 5.5 mm bayonet,
LANCOM item no. 111303 (not for WW devices)


*) The additional power LED statuses are displayed in 5-seconds
rotation if the device is configured to be managed by the LANCOM
Management Cloud.

Quick Reference Guide

TP Ethernet interface (Uplink)Connect the Uplink interface to a LAN switch or a WAN modem with a suitable cable.
TP Ethernet interfacesUse one of the enclosed cables with the kiwi-colored connectors to connect the interface ETH 1 to ETH 4 to your PC or a LAN switch.
Serial configuration interface For configuration, connect the device and a PC with a configuration cable (cable sold separately).
USB interfaceYou can use the USB interface to connect a USB printer or a USB flash drive for device configuration
Reset buttonPressed up to 5 seconds: device restart Pressed until first flashing up of all LEDs: configuration reset and device restart
PowerAfter connecting the cable to the device, turn the bayonet connector 90° clockwise until it clicks into place.Use only the supplied power adapter.
Please observe the following when setting up the device
A The mains plug of the device must be freely accessible.
A For devices to be operated on the desktop, please attach the adhesive rubber
A Do not rest any objects on top of the device and do not stack multiple devices.
A Keep the ventilation slots on the side of the device clear of obstruction.
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This docu-
ment contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions. 111974/0421
Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.
b c d
AP Status
a db fec
a Power
Off Device switched off
Green, permanently* Device operational,
resp. device paired / claimed and LANCOM
Management Cloud (LMC) accessible
Green/orange, blinking Configuration password not set. Without a
configuration password, the configuration
data in the device is unprotected.
Red, blinking Charge or time limit reached
1x green inverse
Connection to the LMC active, pairing OK,
device not claimed
2x green inverse
Pairing error, resp. LMC activation code
not available
3x green inverse
LMC not accessible, resp. communication
e Online
Off WAN connection inactive
Green, permanently WAN connection active
Red, permanently WAN connection error
Off No VPN connection active
Green, permanently VPN connection active
Green, blinking Establishing VPN connections
Off No networking device attached
Green, permanently Connection to network device operational,
no data traffic
Green, flickering Data transmission
b AP Status
Green, permanently At least one active access point is con-
nected and authenticated; no new and no
missing access point.
Green/orange, blinking At least one new access point.
Red, permanently The LANCOM Wi-Fi controller is not yet
operational; one of the following elements
is missing:
a Root certificate
a Device certificate
a Current time
a Random number for the DTLS encryption
Red, blinking At least one of the expected access points
is missing.
c Uplink
Off No networking device attached
Green, permanently Connection to network device operational,
no data traffic
Green, flickering Data transmission

Ver el manual de Lancom WLC-30 aquí, gratis. Este manual pertenece a la categoría No categorizado y ha sido calificado por 1 personas con un promedio de 7.5 . Este manual está disponible en los siguientes idiomas: Inglés . ¿Tienes alguna pregunta sobre Lancom WLC-30 o necesitas ayuda? Haz tu pregunta aquí

¿Necesitas ayuda?

¿Tiene alguna consulta sobre el Lancom y la respuesta no está en el manual? Haga su consulta aquí. Proporcione una descripción clara y completa de su problema y su consulta. Cuanto mejor describa su problema y consulta, más fácil será para otros propietarios de Lancom proporcionarle una buena respuesta.

Número de preguntas: 0

WLC-30 | 61789
No categorizado
4044144617898, 5704174938828
Manual de usuario (PDF)
Ethernet LAN, velocidad de transferencia de datos10,100,1000 Mbit/s
Soporte VPNIKE, IKEv2\nIPv4, IPv6 VPN
Límite de rangoSi
Estándares de redIEEE 802.11e, IEEE 802.11i, IEEE 802.11w, IEEE 802.1Q, IEEE 802.1x
Puertos e Interfaces
Puertos Ethernet LAN (RJ-45)5
Cantidad de puertos USB 2.01
Contenido del empaque
Cables incluidosLAN (RJ-45)
CertificaciónCE EN 62368, EN 55022, EN 55024
Datos de logística
País de origenAlemania
Código de Sistema de Armonización (SA)85176990
Peso y dimensiones
Peso450 g
Ancho210 mm
Profundidad140 mm
Altura45 mm
Condiciones ambientales
Intervalo de temperatura operativa (T-T)0 - 40 °C
Intervalo de humedad relativa para funcionamiento0 - 95 %
Control de energía
Voltaje de entrada DC12 V
Voltaje de entrada230 V
Características de administración
Calidad de servicio (QoS) soporteSi
Multidifusión, soporteSi
Algoritmos de seguridadAES-CCMP, AES-GCMP, SNMP, SNMPv2, SNMPv3, TKIP, WPA, WPA2, WPA2-PSK, WPA3-Enterprise, WPA3-PSK
Lista negraSi
Seguridad con cortafuegosSi
Soporte VLANSi
Protocolos de gestiónSSL, SSH, HTTPS, Telnet, TFTP, SNMP, HTTP
Protocolos de red compatiblesARP, proxy ARP, BOOTP, DHCP, DNS, HTTP, HTTPS, IP, ICMP, NTP/SNTP, NetBIOS, PPPoE (server), RADIUS, RIP-1, RIP-2, RTP, SIP, SNMP, TCP, TFTP, UDP, VRRP, VLAN
mostrar más

¿No puede encontrar la respuesta a su consulta en el manual? Puede encontrar la respuesta a su consulta en las preguntas frecuentes sobre el Lancom WLC-30 más abajo.

¿No aparece tu pregunta? Haz tu pregunta aquí

No hay resultados